Difference between revisions of "Recover Cyclades ACS600 to factory defaults"
(One intermediate revision by the same user not shown) | |||
Line 2: | Line 2: | ||
1. Download the ACS6000 firmware and save the file in C:\ of the local PC - http://www.avocent.com/Support_Firmware/ACS/ACS_6000_Advanced_Console_Servers.aspx | 1. Download the ACS6000 firmware and save the file in C:\ of the local PC - http://www.avocent.com/Support_Firmware/ACS/ACS_6000_Advanced_Console_Servers.aspx | ||
+ | |||
2. Run Solwarwinds TFTP server and configure the TFTP Server Root Directory - C:\ | 2. Run Solwarwinds TFTP server and configure the TFTP Server Root Directory - C:\ | ||
+ | |||
3. Access ACS6000 Serial Console | 3. Access ACS6000 Serial Console | ||
+ | |||
4. Power cycle ACS6000 | 4. Power cycle ACS6000 | ||
+ | |||
5. On ACS6000 during "Hit any key to stop autoboot", press a key and enter the following commands at the shell prompt: | 5. On ACS6000 during "Hit any key to stop autoboot", press a key and enter the following commands at the shell prompt: | ||
setenv bootfile fl0585010.bin <----ACS6000 firmware | setenv bootfile fl0585010.bin <----ACS6000 firmware | ||
Line 13: | Line 17: | ||
You should see many ###### during the firmware transfering. If you see many T T T T T, transfer timeout, please check your firewall and the port 69 for TFTP. | You should see many ###### during the firmware transfering. If you see many T T T T T, transfer timeout, please check your firewall and the port 69 for TFTP. | ||
+ | |||
6. Once completed, it will ask you to type the login username: | 6. Once completed, it will ask you to type the login username: | ||
Type- Username: root; Pasword: linux | Type- Username: root; Pasword: linux | ||
+ | |||
7. After booting, login as root and execute the following at the shell prompt; | 7. After booting, login as root and execute the following at the shell prompt; | ||
recover-flash.sh --doformat --factory_default | recover-flash.sh --doformat --factory_default | ||
reboot | reboot | ||
− | + | '''Note:''' The steps are for firmware version 2.0 and newer. If the unit is running firmware 1.x please enter "shell" after login to enter to the command shell |
Latest revision as of 06:52, 26 April 2013
Taken from [1]
1. Download the ACS6000 firmware and save the file in C:\ of the local PC - http://www.avocent.com/Support_Firmware/ACS/ACS_6000_Advanced_Console_Servers.aspx
2. Run Solwarwinds TFTP server and configure the TFTP Server Root Directory - C:\
3. Access ACS6000 Serial Console
4. Power cycle ACS6000
5. On ACS6000 during "Hit any key to stop autoboot", press a key and enter the following commands at the shell prompt:
setenv bootfile fl0585010.bin <----ACS6000 firmware setenv serverip 192.168.10.30 <----TFTP server (Local PC) IP Address setenv ipaddr 192.168.10.40 <-----ACS6000 IP Address saveenv net_boot factory_default
You should see many ###### during the firmware transfering. If you see many T T T T T, transfer timeout, please check your firewall and the port 69 for TFTP.
6. Once completed, it will ask you to type the login username:
Type- Username: root; Pasword: linux
7. After booting, login as root and execute the following at the shell prompt;
recover-flash.sh --doformat --factory_default reboot
Note: The steps are for firmware version 2.0 and newer. If the unit is running firmware 1.x please enter "shell" after login to enter to the command shell