Determine Interface Status
From Peter Pap's Technowiki
Revision as of 03:22, 5 October 2010 by Ppapa (talk | contribs) (Created page with "The following script will give you the status of your active network interfaces, ie. duplex, speed, auto-negotiation etc. Was taken from a BigAdmin article: #!/bin/ksh ##...")
The following script will give you the status of your active network interfaces, ie. duplex, speed, auto-negotiation etc. Was taken from a BigAdmin article:
#!/bin/ksh
################################################################################
# Simple script to GET stats about network cards
# Should work on hme and qfe. Will NOT change anything.
# Will report on speed and config of all network interfaces.
# Paul Bates 27.03.2000
# James Council 26.09.2001
# - Changed output to one liners.
# - Added IPversion check.
# James Council 10.10.2002 (jamescouncil@yahoo.com)
# - Added test for Cassini Gigabit-Ethernet card (ce_).
# - Added test for GEM Gigabit-Ethernet (ge_)
# - Added test for eri Fast-Ethernet (eri_).
# - Added "Ethernet Address" field.
# - Removed "IPversion" field.
# - Removed checking of a port more than once (i.e. qfe0 qfe0:1)
# James Council 10.25.2002 (jamescouncil@yahoo.com)
# - Fixed 1GB check on ge device.
# James Council 04.02.2003 (jamescouncil@yahoo.com)
# - Added dmfe check (suggested by John W. Rudick, & Erlend Tronsmoen)
# Octave Orgeron 02.06.2004 (unixconsole@yahoo.com)
# - Added bge check (bge_).
# Octave Orgeron 05.18.2005 (unixconsole@yahoo.com)
# - Corrected CE check to use kstat, which is required in Solaris 10.
# Octave Orgeron 12.13:2005 (unixconsole@yahoo.com)
# - Corrected CE and DMFE check. Added IPGE check. Special thanks to
# Paul Bates, Christian Jose, and Bill Qualye for suggesting fixes and
# for keeping me on my toes;)
# Octave Orgeorn 02.07.2007 (unixconsole@yahoo.com)
# - Added support for the Intel e1000g interfaces.
# - Cleaned up script. Housecleaning.
# - Tested against Fujitsu Quad GigE Nic's (FJGI)
# Paul Bates 10.03.2008 (sun@paulbates.org)
# - included NXGE interfaces, Thanks Jorg Weiss and Randy Latimer !!
# - Just tidied up code a little more, removed some fluff
#
# NOTE: For further updates or comments please feel free to contact me via
# email. James Council or Octave Orgeron or Paul Bates
#
################################################################################
NDD=/usr/sbin/ndd
KSTAT=/usr/bin/kstat
IFC=/sbin/ifconfig
DLADM=/usr/sbin/dladm
typeset -R10 LINK
typeset -R8 AUTOSPEED
typeset -R8 STATUS
typeset -R8 SPEED
typeset -R8 MODE
typeset -R18 ETHER
# Function to test that the user is root.
Check_ID()
{
ID=$(/usr/ucb/whoami)
if [ $ID != "root" ]; then
echo "$ID, you must be root to run this program."
exit 1
fi
}
# Function to test Quad Fast-Ethernet, Fast-Ethernet, and
# Gigabit-Ethernet (i.e. qfe_, hme_, ge_, fjgi_)
Check_NIC()
{
${NDD} -set /dev/${1} instance ${2}
if [ $type = "ge" ];then
autospeed=`${NDD} -get /dev/${1} adv_1000autoneg_cap`
else
autospeed=`${NDD} -get /dev/${1} adv_autoneg_cap`
fi
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${NDD} -get /dev/${1} link_status`
case $status in
1) STATUS=UP ;;
0) STATUS=DOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${NDD} -get /dev/${1} link_speed`
case $speed in
1000) SPEED=1GB ;;
1) SPEED=100MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${NDD} -get /dev/${1} link_mode`
case $mode in
1) MODE=FDX ;;
0) MODE=HDX ;;
*) MODE=ERROR ;;
esac
}
# Function to test the Davicom Fast Ethernet, DM9102A, devices
# on the Netra X1 and SunFire V100 (i.e. dmfe_)
Check_DMF_NIC()
{
autospeed=`${NDD} -get /dev/${1}${2} adv_autoneg_cap`
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${NDD} -get /dev/${1}${2} link_status`
case $status in
1) STATUS=UP ;;
0) STATUS=DOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${NDD} -get /dev/${1}${2} link_speed`
case $speed in
100) SPEED=100MB ;;
10) SPEED=10MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${NDD} -get /dev/${1}${2} link_mode`
case $mode in
2) MODE=FDX ;;
1) MODE=HDX ;;
0) MODE=UNKOWN ;;
*) MODE=ERROR ;;
esac
}
# Function to test a Cassini Gigabit-Ethernet (i.e. ce_).
Check_CE()
{
autospeed=`${KSTAT} -m ce -i $num -s cap_autoneg | grep cap_autoneg | awk '{print $2}'`
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${KSTAT} -m ce -i $num -s link_up | grep link_up | awk '{print $2}'`
case $status in
1) STATUS=UP ;;
0) STATUS=DOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${KSTAT} -m ce -i $num -s link_speed | grep link_speed | awk '{print $2}'`
case $speed in
1000) SPEED=1GB ;;
100) SPEED=100MB ;;
10) SPEED=10MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${KSTAT} -m ce -i $num -s link_duplex | grep link_duplex | awk '{print $2}'`
case $mode in
2) MODE=FDX ;;
1) MODE=HDX ;;
0) MODE=UNKNOWN ;;
*) MODE=ERROR ;;
esac
}
# Function to test Sun BGE interface on Sun Fire V210 and V240.
# The BGE is a Broadcom BCM5704 chipset. There are four interfaces
# on the V210 and V240. (i.e. bge_)
Check_BGE_NIC()
{
autospeed=`${NDD} -get /dev/${1}${2} adv_autoneg_cap`
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${NDD} -get /dev/${1}${2} link_status`
case $status in
1) STATUS=UP ;;
0) STATUS=DOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${NDD} -get /dev/${1}${2} link_speed`
case $speed in
1000) SPEED=1GB ;;
100) SPEED=100MB ;;
10) SPEED=10MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${NDD} -get /dev/${1}${2} link_duplex`
case $mode in
2) MODE=FDX ;;
1) MODE=HDX ;;
0) MODE=UNKNOWN ;;
*) MODE=ERROR ;;
esac
}
# Function to test a Intel 82571-based ethernet controller port (i.e. ipge_).
Check_IPGE()
{
autospeed=`${KSTAT} -m ipge -i $num -s cap_autoneg | grep cap_autoneg | awk '{print $2}'`
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${KSTAT} -m ipge -i $num -s link_up | grep link_up | awk '{print $2}'`
case $status in
1) STATUS=UP ;;
0) STATUS=DOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${KSTAT} -m ipge -i $num -s link_speed | grep link_speed | awk '{print $2}'`
case $speed in
1000) SPEED=1GB ;;
100) SPEED=100MB ;;
10) SPEED=10MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${KSTAT} -m ipge -i $num -s link_duplex | grep link_duplex | awk '{print $2}'`
case $mode in
2) MODE=FDX ;;
1) MODE=HDX ;;
0) MODE=UNKNOWN ;;
*) MODE=ERROR ;;
esac
}
# Function to test a Intel 82571-based ethernet controller port (i.e. e1000g_).
Check_E1KG()
{
autospeed=`${KSTAT} -m e1000g -i $num -s cap_autoneg | grep cap_autoneg | awk '{print $2}'`
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${KSTAT} -m e1000g -i $num -s link_up | grep link_up | uniq |awk '{print $2}'`
case $status in
1) STATUS=UP ;;
0) STATUS=DOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${KSTAT} -m e1000g -i $num -s link_speed | grep link_speed | awk '{print $2}'`
case $speed in
1000) SPEED=1GB ;;
100) SPEED=100MB ;;
10) SPEED=10MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${KSTAT} -m e1000g -i $num -s link_duplex | grep link_duplex | awk '{print $2}'`
case $mode in
2) MODE=FDX ;;
1) MODE=HDX ;;
0) MODE=UNKNOWN ;;
*) MODE=ERROR ;;
esac
}
# Function to test Sun NXGE interface on Sun Fire Tx000.
Check_NXGE_NIC()
{
autospeed=`${NDD} -get /dev/${1}${2} adv_autoneg_cap`
case $autospeed in
1) AUTOSPEED=ON ;;
0) AUTOSPEED=OFF ;;
*) AUTOSPEED=ERROR ;;
esac
status=`${DLADM} show-dev ${1}${2} 2> /dev/null | awk '{print $3;}'`
case $status in
up) STATUS=UP ;;
down) STATUS=DOWN ;;
unknown) STATUS=UNKNOWN ;;
*) STATUS=ERROR ;;
esac
speed=`${DLADM} show-dev ${1}${2} 2> /dev/null | awk '{print $5;}'`
case $speed in
1000) SPEED=1GB ;;
100) SPEED=100MB ;;
10) SPEED=10MB ;;
0) SPEED=10MB ;;
*) SPEED=ERROR ;;
esac
mode=`${DLADM} show-dev ${1}${2} 2> /dev/null | awk '{print $NF;}'`
case $mode in
full) MODE=FDX ;;
half) MODE=HDX ;;
unknown) MODE=--- ;;
*) MODE=ERROR ;;
esac
}
#############################################
# Start
#############################################
Check_ID
echo "\n Link: Auto-Neg: Status: Speed: Mode: Ethernet Address:"
echo "---------------------------------------------------------------------"
# Create a uniq list of network ports configured on the system.
# NOTE: This is done to avoid multiple references to a single network port
# (i.e. qfe0 and qfe0:1).
NICS=`${IFC} -a| egrep -v "lo|be|dman|lpfc|jnet"| awk -F: '/^[a-z,A-z]/ {print $1}'| sort -u`
for LINK in $NICS
do
if [ `echo $LINK | grep e1000g` ]
then
type=e1000g
num=$(echo $LINK | cut -f2 -d"g")
else
type=$(echo $LINK | sed 's/[0-9]//g')
num=$(echo $LINK | sed 's/[a-z,A-Z]//g')
fi
# Here we reference the functions above to set the variables for each port which
# will be outputed below.
case ${type} in
bge) Check_BGE_NIC $type $num ;;
ce) Check_CE $type $num ;;
dmfe) Check_DMF_NIC $type $num ;;
ipge) Check_IPGE $type $num ;;
e1000g) Check_E1KG $type $num ;;
nxge) Check_NXGE_NIC $type $num ;;
*) Check_NIC $type $num ;;
esac
# Set ethernet variable and output all findings for a port to the screen.
ETHER=`$IFC $LINK| awk '/ether/ {print $2}'`
echo "$LINK $AUTOSPEED $STATUS $SPEED $MODE $ETHER"
done
#############################################
# End
#############################################
##############################################################################
### This script is submitted to BigAdmin by a user of the BigAdmin community.
### Sun Microsystems, Inc. is not responsible for the
### contents or the code enclosed.
###
###
### Copyright Sun Microsystems, Inc. ALL RIGHTS RESERVED
### Use of this software is authorized pursuant to the
### terms of the license found at
### http://www.sun.com/bigadmin/common/berkeley_license.jsp
##############################################################################
