Difference between revisions of "Recover Cyclades ACS600 to factory defaults"

From Peter Pap's Technowiki
Jump to: navigation, search
(Created page with "Taken from [http://community.emerson.com/networkpower/support/avocent/serial/acs6000/w/wiki/2726.acs6000-recovery-process-set-factory-defaults.aspx] 1. Download the ACS6000 firmw...")
 
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
Taken from [http://community.emerson.com/networkpower/support/avocent/serial/acs6000/w/wiki/2726.acs6000-recovery-process-set-factory-defaults.aspx]
 
Taken from [http://community.emerson.com/networkpower/support/avocent/serial/acs6000/w/wiki/2726.acs6000-recovery-process-set-factory-defaults.aspx]
 +
 
1. Download the ACS6000 firmware and save the file in C:\ of the local PC - http://www.avocent.com/Support_Firmware/ACS/ACS_6000_Advanced_Console_Servers.aspx
 
1. Download the ACS6000 firmware and save the file in C:\ of the local PC - http://www.avocent.com/Support_Firmware/ACS/ACS_6000_Advanced_Console_Servers.aspx
 +
 
2. Run Solwarwinds TFTP server and configure the TFTP Server Root Directory - C:\
 
2. Run Solwarwinds TFTP server and configure the TFTP Server Root Directory - C:\
 +
 
3. Access ACS6000 Serial Console
 
3. Access ACS6000 Serial Console
 +
 
4. Power cycle ACS6000
 
4. Power cycle ACS6000
 +
 
5. On ACS6000 during "Hit any key to stop autoboot", press a key and enter the following commands at the shell prompt:
 
5. On ACS6000 during "Hit any key to stop autoboot", press a key and enter the following commands at the shell prompt:
 
     setenv bootfile fl0585010.bin  <----ACS6000 firmware
 
     setenv bootfile fl0585010.bin  <----ACS6000 firmware
Line 12: Line 17:
  
 
You should see many ###### during the firmware transfering. If you see many T T T T T, transfer timeout, please check your firewall and the port 69 for TFTP.
 
You should see many ###### during the firmware transfering. If you see many T T T T T, transfer timeout, please check your firewall and the port 69 for TFTP.
 +
 
6. Once completed, it will ask you to type the login username:
 
6. Once completed, it will ask you to type the login username:
 
     Type- Username: root; Pasword: linux
 
     Type- Username: root; Pasword: linux
 +
 
7. After booting, login as root and execute the following at the shell prompt;
 
7. After booting, login as root and execute the following at the shell prompt;
 
     recover-flash.sh --doformat --factory_default
 
     recover-flash.sh --doformat --factory_default
 
     reboot
 
     reboot
  
    Note: The steps are for firmware version 2.0 and newer. If the unit is running firmware 1.x please enter "shell" after login to enter to the command shell
+
'''Note:''' The steps are for firmware version 2.0 and newer. If the unit is running firmware 1.x please enter "shell" after login to enter to the command shell

Latest revision as of 06:52, 26 April 2013

Taken from [1]

1. Download the ACS6000 firmware and save the file in C:\ of the local PC - http://www.avocent.com/Support_Firmware/ACS/ACS_6000_Advanced_Console_Servers.aspx

2. Run Solwarwinds TFTP server and configure the TFTP Server Root Directory - C:\

3. Access ACS6000 Serial Console

4. Power cycle ACS6000

5. On ACS6000 during "Hit any key to stop autoboot", press a key and enter the following commands at the shell prompt:

   setenv bootfile fl0585010.bin  <----ACS6000 firmware
   setenv serverip 192.168.10.30 <----TFTP server (Local PC) IP Address
   setenv ipaddr 192.168.10.40 <-----ACS6000 IP Address
   saveenv
   net_boot factory_default

You should see many ###### during the firmware transfering. If you see many T T T T T, transfer timeout, please check your firewall and the port 69 for TFTP.

6. Once completed, it will ask you to type the login username:

   Type- Username: root; Pasword: linux

7. After booting, login as root and execute the following at the shell prompt;

   recover-flash.sh --doformat --factory_default
   reboot

Note: The steps are for firmware version 2.0 and newer. If the unit is running firmware 1.x please enter "shell" after login to enter to the command shell